This job board retrieves part of its jobs from: Toronto Jobs | Emplois Montréal | IT Jobs Canada

The exclusive website bringing you daily job offers!

To post a job, login or create an account |  Post a Job

Maintenance Mechanic

Aerotek

This is a Full-time position in Tarboro, NC posted January 11, 2021.

Description: nnLS Cable is looking for 2 Maintenance Mechanics similar to Millright on PM shift 6pm-6am or 6pm-2am | 10pm-6am or 6pm-6am | Monday-Friday but will be mandatory Saturdays/Sundays some weeks Will train on 1st shift for the 1st 2 weeks This position exists for the purpose of performing tasks such as troubleshooting, repair, and installation of production and support equipment on the night shift operations.

Personally handle general repair work and maintenance on all electrical/electronic components, motors, motor drives, and associated hardware.

Assist with the assembly and installation of new equipment.

Use various hand and power tools and operate all types of electronic troubleshooting equipment.

Perform routine preventive maintenance and servicing tasks such as cleaning, adjusting and inspections on electronic equipment.

ESSENTIAL DUTIES AND RESPONSIBILITIES:
•Repair production and spare equipment when failure is of an electrical or electronic nature.

This requires the ability to do minor soldering, alignment, grinding, disassembly and reassembly of major and minor, large and small pieces of equipment.

Help troubleshoot equipment by observing equipment operation from an electronic perspective.

•Design, fabricate, assemble and install parts, fixtures or entire assemblies as requested by Engineering or Department managers.

•Initiates necessary parts request form for required electronic supplies so repairs or installations can be completed.

•Inspect and calibrate various pieces of production equipment.

•Requires documentation of drawings, layouts, time sheets, work orders and cost reduction or safety proposals.

•Perform other related duties as directed by supervisor.

Looking to have 22 of the following 45 abilities Knowledge of plant lay-out Know main power disconnects on machines Know lockout procedures for machines Install and align pulleys Demonstrate knowledge of basic pneumatics/hydraulics Operate designated power tools Competent in all maintenance paperwork Install timing/motor belts Check oil levels in gearboxes Troubleshoot basic setup errors on a PO/TU Demonstrate basic knowledge of machine operation Maintain shop housekeeping at required level Air compressor: Complete start up /shut down procedures and show ability to troubleshoot overheat issues Perform maintenance on and overhaul of centrifical pumps Perform gearbox overhaul, single and multi speed.

Troubleshoot and repair pneumatic system Replace brass nuts in pay-offs/take-ups Extract broken bolts and screws Clean and rod heat exchanger PM plant equipment Read Tape measure down to 1/16’s Setup Mig welder for use & to materials to be welded Perform flat/horizontal welds ( MIG ) Troubleshoot/Repair compound systems Replace drive belts and properly align on any machine Troubleshoot and repair Hydraulic systems Perform vertical welds (MIG) Use OXY/Acetylene torch Use caliper for shaft and bearing measurements Perform flat and Horizontal Stick welds/ 7018 Alpha Jet Printers: Need to be able to install print legends, verify print quality concerns and correct Plumbing and pipe fitting (all sizes) Perform Vertical stick welds / 7018 Indicate motors to shafts Overhaul wire draw machine Replace take-ups (drive pindles, air cylinders, dancer assembly, Perform Overhead stick welds / 7018 Correctly read machine blueprints and other mechanical schematics, layouts and fabricated complex parts Successfully weld machine parts Solely able to handle all mechanical calls Troubleshoot hydraulic pumps and systems Perform Stick welds/ 7018 Carbon Pipe Tig weld Flat & Vertical Verify parts/materials needed to perform repairs/projects and complete requisition Independently Complete any fabricating project from start to finish/nn Skills: nnMaintenance technician, Hydraulics, Pneumatics, Mechanical, Repair, Troubleshooting, Schematic, Preventive maintenance, Allen-bradleynn Additional Skills & Qualifications: nn.nn Experience Level: nnEntry Levelnn nn nn nn nn About Aerotek: nnWe know that a company’s success starts with its employees.

We also know that an individual’s success starts with the right career opportunity.

As a Best of Staffing® Client and Talent leader, Aerotek’s people-focused approach yields competitive advantage for our clients and rewarding careers for our contract employees.

Since 1983, Aerotek has grown to become a leader in recruiting and staffing services.

With more than 250 non-franchised offices, Aerotek’s 8,000 internal employees serve more than 300,000 contract employees and 18,000 clients every year.

Aerotek is an Allegis Group company, the global leader in talent solutions.

Learn more at Aerotek.com.nn nnThe company is an equal opportunity employer and will consider all applications without regards to race, sex, age, color, religion, national origin, veteran status, disability, sexual orientation, gender identity, genetic information or any characteristic protected by law.nn